SOLVENT RESISTANT MARKING INKS

#432 SOLVENT RESISTANT INK FOR PERMANENT MARKING ON METAL AND PLASTIC PARTS, PRINTED CIRCUIT BOARDS, POLYETHYLENE, POLYPROPYLENE AND OTHER HARD TO MARK SURFACES DESIGNED TO RESIST SOLVENTS SUCH AS DEGREASERS, FREON, ALCOHOL, CLEANING FLUIDS, TRICHORETHYLENE, SOAP AND WATER. THE LONGER THE IMPRESSION IS ALLOWED TO DRY THE MORE STEADFAST THE IMPRESSION BECOMES. ADHESION IS EXCELLENT DRIES IN 10-30 SECONDS COLORS: BLACK, BLUE, GREEN, ORANGE, RED, VIOLET, WHITE & YELLOW PRICES FOR #432 INK ARE: N/A Pint = 43.00 4 oz. = 24.00 Quart = 62.00 8 oz. = 32.00 Gallon = 148.00 ADD 432 INK TO MY CART

1-PART EPOXY INK #6459 FOR PERMANENT STAMPING ON METALS, PLASTICS, CIRCUIT BOARDS AND ALL NON-POROUS SURFACES. #6459 - ONE-PART EPOXY STAMP INK IS FOR MARKING ON ALL NON-POROUS SURFACES. THE PROPERTIES ARE SIMILAR TO A TWO-PART EPOXY, BUT THIS INK DOES NOT MEET GOVERNMENT SPEC. MIL-I-43553. IT DOES RESIST MOST SOLVENTS AND DEGREASERS AND IS MADE WITH TRUE EPOXY RESIN. IT DOES MEET GENERAL DYNAMICS SPECS TO REPLACE 2-PART EPOXY. DRIES IN 10-15 SECONDS TO THE TOUCH AND BECOMES FAIRLY PERMANENT WITHIN 4 HOURS COLORS: BLACK, BLUE, BROWN, GRAY, GREEN, ORANGE, RED, VIOLET, WHITE & YELLOW PRICES FOR #6459 INK ARE: N/A Pint = 46.00 4 oz. = 25.00 Quart = 67.00 8 oz. = 35.00 Gallon = 152.00 CAN BE USED WITH A MARK II PAD, OPAQUE OR STONE PAD ADD 1-PART EPOXY INK TO MY CART

PLEASE NOTE: ALL INK ORDERS AND SPECIAL ORDERS WILL ALWAYS HAVE SHIPPING CHARGES ADDED TO YOUR BILL

2-PART EPOXY INK #6050 FOR VERY PERMANENT STAMPING ON NON-POROUS SURFACES (METALS, GLASS, HARD PLASTICS AND CIRCUIT BOARDS) THIS IS THE ONLY INK THAT MEETS MIL SPEC: MIL-I--43553 - - - WARNING - - - THIS INK IS ONLY RECOMMENDED FOR THOSE APPLICATIONS WHERE YOU HAVE NO CHOICE. IT MUST BE ROLLED OUT TO A THIN LAYER BEFORE USING ON A SHEET OF GLASS OR METAL. THAT IS THEN USED AS THE PAD. THE 2 PARTS MUST BE MIXED BY WEIGHT, NOT BY SIGHT, OR IT WILL NOT MEET THE SPEC. DRYING TIME: AIR CURE IS 5 HOURS TO TOUCH AND 72 HOURS OR MORE FOR MIL SPEC PERMANENCE. DRYING TIME CAN BE SPED UP SUBSTANTIALLY WITH BAKING THE STAMPED PRODUCT. POT LIFE: 3 HOURS - ONCE MIXED MUST BE ROLLED OUT TO A THIN LAYER WITH A BRAYER ON A FLAT SHEET OF GLASS OR METAL BEFORE MARKING. COLORS: BLACK AND WHITE OTHER SIZES ARE AVAILABLE BUT MUST BE MIXED BY WEIGHT PLEASE INQUIRE A CLIP-PAC IS PRE-MEASURED, BY WEIGHT, WITH A CLIP SEPARATING THE TWO COMPONENTS. PULL THE CLIP - MIX THEM TOGETHER, CUT A CORNER OF THE PAC AND USE. 10 cc Clip-Pac 12.00 Each ADD 2-PART EPOXY INK TO MY CART

PLEASE NOTE: ALL INK ORDERS AND SPECIAL ORDERS WILL ALWAYS HAVE SHIPPING CHARGES ADDED TO YOUR BILL

PLEASE READ: INK AND PADS ARE NOT RETURNABLE. WE DO OUR BEST TO DESCRIBE THE CHARACTERISTICS OF OUR INKS, BUT WE CANNOT CONTROL HOW THEY WILL WORK ON EVERY SUBSTRATE AND IN EVERY SITUATION. WE HIGHLY RECOMMEND THAT YOU DO NOT BUY LARGE QUANTITIES UNTIL YOU ARE SURE THAT A SPECIFIC INK MEETS YOUR REQUIREMENTS. THEY WILL WORK AS DESCRIBED UNDER MOST CONDITIONS, BUT IT IS YOUR RESPONSIBILITY TO TEST IT TO MAKE SURE IT DOES WHAT YOU WANT IT TO. IF YOU HAVE SPECIAL REQUIREMENTS OR SPECIFICATIONS PLEASE CLICK HERE TO GO TO INQUIRY FORM OR CALL US - WE NORMALLY HAVE AN INK THAT WILL WORK. NO WARRANTY IS GIVEN ON INKS

SHIPPING CHOICES AND RETURN POLICY - CLICK HERE
Click on the kind of Stamp you are interested in below

SELF INKING STAMPS	PRE INKED STAMPS	HAND STAMPS	NUMBER STAMPS
Plastic DATE & NUMBER STAMPS	DATER STAMPS	INSPECTION STAMPS	HOLE PUNCHES
METAL DATE STAMPS	INKS	CHANGEABLE STAMPS Make Your Own	HOME

EMAIL US: carostamp@charter.net Date Last Modified: 11/19/05

Telephone: 828-759-0132 24 Hour Fax: 828-759-0133

Toll Free

Telephone: 877-759-0132 24 Hour Fax: 877-759-0133